Re: Show both dimenioan parameter & number at teh same time while modelling
While you can apply relations directly to dimensions, it is easier to open the Relations editor. From there when you select a feature it shows all the feature dimensions. Selecting the dimensions of...
View ArticleRe: How do I create a dynamic query?
Here is how I do it in 10.4. This works with any filter you can come up with that will work in the normal query engine. If you are unfamiliar with the syntax, just make a query using their query...
View ArticleRe: S/M flat pattern bend direction & angle notes - change
Paul, Currently there is no option (default) to change the decimal place and attachment for bend note, however you can use workaround for both, as: -- To remove trailing zeros 1. Select Bend note...
View ArticleRe: Simple Riemann sum
Larry Orth wrote: OOk, now I am curious. What software are you moving to.We have not yet settled on a specific software but still are exploring and using Mathcad15 as long as it seems to make sense. Of...
View ArticleRe: units in ODE solvers
I should add that I haven't tested the stiff eq. solvers, only those shown in the prime file.
View ArticleClik here to view.
Re: Hidden lines display and PDF files : the big mystery ...
Ah yes, so it's 1 and not 0 then. Could you post the contents your pnt file here? Mine is still set as you can see in the post up above, that means I print in all black. Well, as for the mapkey...
View ArticleRe: Creo 2.0 Installation
Sylar, This issue may occour due to installmgr.dll in installation media. You can download another version of that from https://www.ptc.com/appserver/cs/view/solution.jsp?n=CS151686
View ArticleRe: Hidden lines display and PDF files : the big mystery ...
PDF/A is the Archive suggested practice. The main requirement is the file have no external references, such as referring to fonts that are supposed to be loaded by the PDF processor; instead fonts are...
View ArticleClik here to view.
Re: Hidden lines display and PDF files : the big mystery ...
Assuming you are referring to my pen table, it is attached. I am only working in gray and black with two line thicknesses however as can be seen form the image above, centerlines and axes appear in a...
View ArticleRe: Hidden lines display and PDF files : the big mystery ...
Yeah I briefly skimmed over the wiki earlier today and couldn't see how PDF/A offered me any benefit.
View ArticleRe: Maintenance: Restarting Servers
There's no official recommendation from PTC about how often to restart the servers. Theoretically, they shouldn't ever need to be restarted, unless you make a configuration change that requires a...
View ArticleRe: Impact Analysis / Drop Test Simulation
Ben, The 6DOF joint needs to be defined in a mechanism analysis. The tutorial above is a 2 part process.First you run a mechanism analysis to get the values and contact areas then you use those...
View ArticleRe: New to Creo - Parameter Roll-Up in Assemblies
Is there a way to just view the weight value without putting it on a drawing? Or do you need to place is somewhere on the assembly drawing to see it?
View ArticleRe: Impact Analysis / Drop Test Simulation
If acceleration spectrum is known, I would propose a dynamic shock analysis. You would have to create a valid modal analysis model, use it to calculate (a large number of ) normal modes and subject to...
View ArticleRe: Maintenance: Restarting Servers
LDAP should be up when Windchill is started as well. Essentially the back-end datastores should be up first.
View ArticleTruncate dimension in a drawing
In a similar thread, there was a way to truncate the output of a parameter used as a dimension in a drawing (See thread: http://communities.ptc.com/message/191893#191893 ). What I am looking for is to...
View ArticleRe: New to Creo - Parameter Roll-Up in Assemblies
I have added the parameters to the Model Tree as additional columns. That way you can see all the values from the parts that make up the assembly as well.
View ArticleRe: Function mhyper acts quirky in M14 and M15
Mathcad's ode solver seems to be accurate to about 4 or 5 significant figures here.Which you can significantly improve by setting TOL to a lower value than the default 10^-3.
View Article