Re: Old Mathcad MCS image files
yes, but without the quotes, which makes a big difference!
View ArticleRe: Trouble exporting solid part into solidworks
If the parts in creo are purple, then you only have surfaces and not solids. You can convert these to solids by merging the surfaces together then solidify. Once it solidifies, it will be gray in...
View ArticleRe: RE: Wildfire 4.0 Installs; Won't run
Anyone having this problem? It seems similar however, I think it may be tied in to the server?
View ArticleRe: Roughing depth
I notice you use an actual number for the FREE_FEED and RETRACT_FEED. I don't know if you do this to simulate a RAPID motion for those bits, but if so, you can set those two to 0 (zero) in place of the...
View ArticleRe: tracing the edge of a cutting tool (toolpath)
I have played around with that problem a little bit (still not implemented an outline algorithm) and thought I would post that intermediate result in case somebody else would like to give it a try...
View ArticleRe: Workgroup Manager with Solidworks Educational version
I Am just guessing but perhaps educational version of sw limits the types of "add-ins" that can be added in. Wwgm is connected to sw via the add-in method. This is just a guess
View ArticleCreo Parametric 2.0 M100 and Windows 7
PTC Community, I just installed M100 today without any complications. I looked at the applications tab to make sure all of the apps were there, such as cabling, piping, mechanisms, simulate, etc....
View ArticleClik here to view.
Re: Helical Sweep, Ball and Worm Gear Assembly
This can be done at the lead-screw level and maintained with relations. As far as I can tell, this is correct and fully parametric.Funny thing is, I can change the 12.0 and nothing updates until I exit...
View ArticleRe: mechanism in fuel injector(mdx & mdo)
Regardless of what it happening in the specification, the mechanism is a simulation of some sort.If you have a "servo motor" that you are tracking the RPM, then you are asking for a trigger. I am not...
View ArticleHow to create clockwise rotation of shaft in pro e maecahnism
In my case I have assigned pin for the shaft & later defined force motor for the same. But If i run the analysis the shaft is rotating clock & anti clockwise .How to control, only it should run...
View ArticleRe: How to edit a component of an assembly without leaving the assembly?
Hi can you see any of the features ( extrudes etc) in the model tree?
View ArticleClik here to view.
Re: How to edit a component of an assembly without leaving the assembly?
No, the only thing that I can see when I activate a component ( as suggested by Timothy ) is a green diamond indicating the part is active to edit. The screen changes with all the options of extrude,...
View ArticleRe: How to edit a component of an assembly without leaving the assembly?
OOk the features are turned off in the assembly to turn them on :-lclick on th icon in the model tree with the hammerLclick on the tree filters...LClick on Featureslclick applylclick OK now when you...
View ArticleRe: How to edit a component of an assembly without leaving the assembly?
Excellent!! Thanks a lot this was giving me a hard time. Thanks Timothy & Phil!
View ArticleRe: creo 2.0 student edition not running after a succesful installation
Hi MarkCheli.I tried to download from http and it works. Creo is already running im my pc.Best regards
View ArticleClik here to view.
Re: Helical Sweep, Ball and Worm Gear Assembly
I wasn't actually thinking mechanism. I attached a model similar to what I was thinking. I put the balls in the part model just for now. Just about everything is driven through relations. It takes...
View ArticleClik here to view.
Re: Feature Failure with Repeating Patterns
I absolutely LOVE the SSD combined with the overclocked CPU. I've convinced our IT department to use this as the standard engineering PC going forward. Nice! I ran a couple of those benchmarks,...
View ArticleRe: Windchill Print Service configuration problem
Hello Bryant. "Windchill Print Service license" it is license for "what"? Is it for Creo View or for Windchill?What do you think about configuration of windchill print service, i doing it correct?
View ArticleReport studio fetches data from WBR on the second run of the report
Hi , I have created a report in WBR using the Query Builder approach. I have a prompt page on the report which provides the input paramaters based on which the report is to be run. When I run the...
View ArticleCtrl+Q won't cycle through labels anymore [Mathcad Prime 3.0]
I don't know what I did but for some reason when I press Ctrl+Q, nothing happens whereas it used to let me cycle through the labels. Could anyone help me fix this? Thank you.
View Article