Re: Problem with jumper wire in NWF (neutral wire file) in WF4
HI Mike... A net is definitely something else. In fact this was one command I was going to use for my first Ninja Cabling presentation because no one I've ever encountered seemed to know what it was. I...
View ArticleRe: project tool in sketch, there has to be a better way!
Hi Gary, I´m glad you could make it easily. I want to share more options with you, but for these, you need Flexible Modeling module: 1 - With the Move or Offset Feature (works even with non-planar...
View ArticleRe: Can you make a closed and tangent-to-itself datum curve in Creo 2.0?
well, the datum points are what I measured with the CMM.and it's the red curve that's correct - my actual part is a disk with an elliptical hole cut out of it.I'm trying to reverse-engineer that shape.
View ArticleClik here to view.
Re: Can you make a closed and tangent-to-itself datum curve in Creo 2.0?
Paul, you can add 2 points where you make the curve segment straight on both ends (choose the line option for that segment). This will make the ends of the curve tangent as well. The 3 points on top...
View ArticleRe: Can you make a closed and tangent-to-itself datum curve in Creo 2.0?
I do see what you mean about a sketch not behaving once you close the spline. The way around it is to divide the spline somewhere along the spline and letting that be tangent. You can then close the...
View ArticleClik here to view.
Re: How do I convert a value from ANSI to ISO format within a table cell
I know there is a setting for making metric (SI) dims with commas, but I am not sure that is the case with equations in relations or even parameters. Look for decimal_marker in drawing .dtl settings,...
View ArticleRe: Can you make a closed and tangent-to-itself datum curve in Creo 2.0?
The little glitch will be much smaller when a decent number of points is chosen. They should be much closer together where the curvature is higher to better follow the surface. I thought there was a...
View ArticleClik here to view.
Re: Can you make a closed and tangent-to-itself datum curve in Creo 2.0?
You'd think that's true, huh I tried that but if it is a single spline in a sketch, it jumps to closing the spline even if you have other geometry there. The Datum Curve version doesn't do that...
View ArticleRe: Can you make a closed and tangent-to-itself datum curve in Creo 2.0?
The end points don't start out with the end points coincident... That's after the tangency is established.
View ArticleClik here to view.
Re: Is it me or has PTC lost it's way
After reading all these posts tonight I have to say the "frustration" expressed by everyone is very real and very familar. I am in no way trying to mitgate the validity of the issues. Take my ideas as...
View ArticleRe: Can you make a closed and tangent-to-itself datum curve in Creo 2.0?
Yes, it can capture whatever you select of the whole screen. It was a quick video and it probably doesn't get the full impact of what I am trying to show. I am not sure what happens if you make the...
View ArticleRe: Creo2: Create 3D model Annotation/Note Flat to Screen with a Leader?
Ryan, I do like Screencast better than Camstudio. It does mess with the "fluidity" of Creo, but if you know to expect it, you can compensate. Do you know if you can change highlight colors when you...
View ArticleClik here to view.
Re: MathCAD URGENT
Many people here scan all Mathcad relevant subspaced so there is absolutely no need to crosspost in three different areas, even though you may consider your question as exceptionally important.If...
View ArticleRe: Can you make a closed and tangent-to-itself datum curve in Creo 2.0?
No sweat - it's better than my videos. In the days before Intent Manager it was often a challenge when nearly vertical or horizontal line segments were required. One would have to exaggerate the...
View ArticleRe: asyncoremt.dll file is missing
Hi AllI have also come across this issue (asyncoremt.dll missing). In fact its quite common in my environment where i would say 75% of the machines ive installed in on give this error. (I install it...
View ArticleRe: asyncoremt.dll file is missing
You can always move the file to the windows folder where all the other .DLL files reside. It will probably throw up a second error with a different file... do the same again.
View ArticleRe: asyncoremt.dll file is missing
Thanks for the promt reply.For some unknown reason on the 7th try at installing it this time it worked fine, not throwing the missing asyncoremt.dll error.Strange?...But its working!
View ArticleClik here to view.
Re: Can you make a closed and tangent-to-itself datum curve in Creo 2.0?
Wait till you give this a try for yourself, David Splines are pretty dumb in Creo.
View ArticleRe: Can you make a closed and tangent-to-itself datum curve in Creo 2.0?
Edit, Matt- I can make the ends of a datum curve through points normal to a plane but not to itself. So you could have a tangency, but it is not defined that way. Datum curve through points...
View Article