Zeichnungsformate in ISO 7200
Hallo zusammen, bisher ist mir hier im Forum immer gut geholfen worden.Daher möchte ich die Zeichnungsvorlagen nach EN ISO 7200einstellen. Mit freundlichem GrußWerner
View ArticleBMX 'Feasibility Study' convergence
I spent today playing (or possibly fighting) with the Feasibility Study in BMX. I'm doing a flotation analysis, so I've got a model of the hull and a 'waterline' plane at a parametric pitch angle and...
View ArticleClik here to view.
Re: Feature Failure with Repeating Patterns
I took another look at the efficiency of the cube. I applied a "Hail Mary" value to the diagonal's pattern fill section by making the width 2x the "big_cube"In fact, you only need 2x "big_cube" minus...
View ArticleDid your Maintenance invoice go up?
My maintenance invoice went up 3% this year. Anyone else experience this? That Makerbot sure is looking like a bargain compared to PTC maintenance!
View ArticleRe: Create Wizard not closing when complete in Windchill 10.1
There are no errors in any logs. I am using Internet Explorer, I also tried it with Mozilla FireFox and had the same issue. I don't have a custom processor, I'm using the ootb...
View ArticleTrying to change the Organization Internet Domain name
I just installed Windchill 10.2 and discovered that the Organization Internet Domain name was incorrect. Following an instruction document from PTC (CS115451) that gives instructions on how to change...
View ArticleClik here to view.
Re: how to measure area in drawing mode
but i don't have a 3d model! it's a layout of a factory. why can't ptc make it possible to measure in 2D when it's available in 3D. the concept is the same after all.i already know the workaround to...
View ArticleClik here to view.
Numeric inaccuracy - bug? (MC15 and Prime)
This is a real strange effect. I know that the conversion from decimal to binary and back can result in numeric inaccuracy. Especially as numbers like 0.7 or 0.1 have a periodic binary representation...
View ArticleClik here to view.
Re: Feature Failure with Repeating Patterns
1:34:00 to regenerate a 9x9x9 cube. 2383 features 305Mb on save (wireframe display) This is using a pattern - copy geometry for the 3 "normal" columns. Ram was well managed during the regeneration....
View ArticleRe: Can you say what is in the collapsed area?
Thanks Werner and Richard for the interest on this problem.It was not only a joke but a point on one problem: formula in book and formula in Mathcad. Can you show one more examples? PSThe collapsed...
View ArticleClik here to view.
Re: Displaying parameters as fractions
Hi Brian !You need to open the dimensions properties and change the format from decimal to fractional, as showed in the image below.Best regards
View ArticleCreo2: Create 3D model Annotation/Note Flat to Screen with a Leader?
This could be done in ProE WF4, but it looks absent from Creo2. We can even place a 3D Note in the model with a leader but when we change it from a planar surface to Flat to Screen the Leader...
View ArticleRe: Mapping creator attribute in desktop integration
Sven, Thanks for the follow up question. PTC responded with a solution further down in the thread. Joel
View ArticleRe: Mapping creator attribute in desktop integration
Thanks Scott. We'll give it a try.
View ArticleClik here to view.
Re: Displaying parameters as fractions
A fraction in its simplest form is an equation (division). You could make the parameter "numerator" and "denominator" and do the math on the decimal value. Use [.n] to control the number of digits....
View ArticleRe: Displaying parameters as fractions
I'm just curious about the rise in interest in using fractions. It's probably easier to create parameters that are parts of the fraction to begin with - whole part, denominator, numerator and use a...
View ArticleClik here to view.
Re: how to measure area in drawing mode
The following is intended to be humorous, but is just as likely to be true... Based on past performance, PTC has feature locked Creo 5, due out no sooner than 3 years and won't consider adding any new...
View ArticleRe: Multi-Language drawings in Productview - How to?
Hello, We are still facing this challenge, and I notice that many colleagues are entering this topic, it has many views. Would it be possible to have a reply? From PTC maybe? Thank you very much,Alex...
View ArticleRe: How to insert a PDF in detail
thank you.sure, all support i could get show that the PDF need to convert a picture format (like BMP and other) then can easily insert. but it is paid by resolution. Best regards, Hongjie
View Article