Re: Using match function in a loop
I didn't notice the second sheet. However, the second sheet is just reproducing the last two columns of sheet 1.
View ArticleWould someone be so kind to convert the file?
Hey there,I have received a file from my colleague which was made in MC 15, I would really appreciate if someone could convert it into mcdx (Prime 2) file since I can not handle it (do not have MC 15...
View ArticleRe: Would someone be so kind to convert the file?
If you have a valid license for Prime you're entitled to a copy of Mathcad 15 under the same license.
View ArticleClik here to view.
Re: How to show datum axis on cylinder in creo 2.0
The display of the datum axis in a drawing is controlled by the Show Model Annotations window. To show an axis: Select Show Model AnnotationsActivate the Datum Tab and Select AllSelect the desired...
View ArticleRe: Would someone be so kind to convert the file?
Did not know that but it won`t help me anyway because we are working on them (Prime) on the university and we (me and colleague) should have done it during the classes. He had installed the trial for...
View ArticleClik here to view.
Summation Operator and Simplifying.
Hello Everybody. My MC14, have not answered with any output, which I may correct some errors in the expression.I wish have any help for correcting the expression (the red one) that may have just...
View ArticleRe: more-than-2 dimensions matrix
but it really seems some times that Mathcad's limits are easily reached...Sometimes that is true. The really sad thing about this is that it did not have to be true. All of the things we have been...
View ArticleRe: Dimension to datums not shown
Thanks, I have voted for this idea as it can be very useful when detailing complex parts or large assemblies.
View ArticleRe: Simple beam with gravity load; displacement does not change when in tension
Jonathan, Yes, your response makes perfect sense. I ran a non-linear analysis with LDA and the results were as I expected; more horizontal tension, less vertical deflection. Thanks much! Chris
View ArticleCreo Simulate - Parameter definition from fastener menu selections
I typically will use a good amount of fasteners and will also set up parameters to pass variables to either sensitivity or optimization studies. For example, I may want to vary fastener diameter, etc....
View ArticleRe: Sync on Effective Date?
Any success in syncing the effectivity? I am searching for a way to do the same thing.
View ArticleRe: Sync on Effective Date?
No. chatted with PTC but they did not have ideas.What I ended up doing was adding a Effectivity tab on the Document types so users can see if it is effective already or not. I would still like to have...
View ArticleRe: more-than-2 dimensions matrix
I don't think it is just the interface, although that's the most obvious. Sometimes, it is easier to tear a building down and build a new one with a proper architecture, rather than adding floors on...
View ArticleRe: ISODraw requires internet connectivity
Hi Tim, The environment variable points to a location on the local hard drive. It is a node lock license. Lisa
View ArticleRe: ISODraw requires internet connectivity
Hi Lisa, I think the most probable cause is that your license is bound to a Wifi mac address instead of a ethernet one.Since these are unavailable when not connected to a network the mac address will...
View ArticleClik here to view.
Need help with proving.
Hello Everybody. I need help with proving the above, in general case for p. Thank you in advance. Best Regards.
View ArticleClik here to view.
Re: document reviews in integrity
The document is not an attachement, it's an integrity document. The review findings should apply to a specific baseline of this doument. I dont want read the review comment from a earlier baseline of...
View ArticleRe: Going to Creo 3 from Inventor and Solidworks
Rohit, File-Open action is implemented for CATIA, Solidworks, NX, only. Martin Hanak
View ArticleRe: more-than-2 dimensions matrix
Valery probably filled the positions with a variable named " ", using [CNTRL-SHIFT-K] [SPACE] [CNTRL-SHIFT-K]. The [CNTRL-SHIFT-K] press allows you to insert (almost) any character into a varaible....
View Article